PLUMBING 101: A GUIDE TO INSTALLING A BATHTUB

Plumbing 101: A Guide to Installing a Bathtub

Plumbing 101: A Guide to Installing a Bathtub

Blog Article

Schedule Appointment Now

Presented here in the next paragraph you can discover a good deal of worthwhile answers around A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is readily accessible, the task can move rapidly; if you need to open a wall surface to eliminate the old tub as well as position the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to leave the old bathtub and set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. Rather than working with a service provider to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will assist you install a new bathtub in your washroom if you have currently bought a new tub as well as do not require to transform the setup of your previous water system pipes.
Your tools and product list must make up the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The process of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is often the case.
    Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
    Before going on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the other end provides a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next off, place the faucet in the mounting opening in the bath/basin making sure that the washing machines are in location in between the faucet as well as the sink. Safeguard the faucet in place with the manufacturer provided backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former type should be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bathtub


    Using the two wooden boards under its feet, place the bath tub in the called for position. The wood boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little points.
    The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub until the level reads level.
    To mount faucets, fit the bottom of the furthest flexible tap port to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
    Activate the water system and inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the bathtub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
    Finally, take care of the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has actually been made use of a minimum of when as this will settle it into its final setting.

    Planning for the Installment


    First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
    Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
    Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the activity experienced when the bathtub is in usage. The sealant can crack rather very early if you do not take into account this activity before securing.
    Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant glue and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    We hope you liked our article about Tools You Need to Install a New Bathtub . Thanks a ton for finding the time to read our piece of content. Sharing is caring. You never know, you could be helping someone out. Kudos for your time. Kindly check our site back soon.


    Quick relief? Dial!

    Report this page